With this device caddy, I experimented with some new (to me) materials and I’m glad I did. I got to try out some new shapes and looks and, my favorite, tools.
Shopping list (I got it all from the ‘steel’ section at a home center):
I’m a Bernzomatic Torch Bearer. I’m not their sales manager. They work with us for design and how-to projects, which is what this is. Now, let’s get down to it.
Design
The goal of this electronics organizer is to create a space for the pile of electronic boxes (pausing for a second to really reflect on just how amazing they are) through which we manage our world: Our phones, pads, tablets. I also want to create a space for their tails: The charger cords that I halfheartedly coil up or hang from a screw or door knob.
I also wanted it to look different than other caddies I’ve seen, so I stepped out of my comfort zone on this and went industrial.
The backbone of my electronics organizer (find other organization tips here) is a punched 1×1 square steel tube. Its purpose is to support the shelf and to be a chase or conduit through which I can run all the cords down to a power source.
How to
I like using a pallet as a work surface when I use my torch. The gaps in the boards and the cavity underneath come in handy all the time. It doesn’t matter if it gets charred from the flame. Finally, a use for pallets that’s not a couch or rope swing or planter. Actually, I like our planter. Check it out here. If you want a pallet couch, watch this VIDEO.
I cut the tube 18-inches. Much longer and it didn’t look right to me hanging on a wall by a door and it was getting longer than many of my cords. Cutting note: I used an angle grinder to cut. It’s an aggressive tool. If you choose to use one, do so carefully.
Next, I notched the tube between punches (holes) about 4-inches down and cut the plate 10-inches long. On both, I knocked down any sharp edges as best I could with the cutting wheel. I also used the grinder to ‘etch’ a texture in the steel. It’s not necessary. I was just playing around. After that, I used my Bernzomatic torch to solder the plate to the tube.
Notice how I notched the pointy part of the square tube (not the flat face). To add some layering and another route for wires, I mitered two more pieces of tube, dry fit them on top of the plate, clipped off their points to create a T-shape. I got that all soldered together Then I cut my 1/2-inch tubing at 8-inches.
I cleaned up the edges on all the tubing on the tool I love for work like this, my mighty bench sander.
Then I soldered the tube to the 1/2-inch tube plate. The idea is to create stops, so you can lean a device without it slipping off.
And that’s really about it. I did learn a few things. The plate and the tube (especially the 1/2-inch tube) heat up at different rates so getting the solder to stick was a challenge. I applied so much heat that the metal deformed (a little) and changed color. I wanted the solder lines to be way more dialed in than they are, too. All told, I got it to work. The look is tough. Also, the cord-ends on charger cords are not all the same. Some fit through the tubing holes, others not so much. But because I ran the tube on a diagonal, there’s a chase along side it that masks cords too. This is also a place to keep cords in the same place because fishing them through takes some effort.
Finally, after scoping out spots in the house for this to take photos I decided the best home for this is inside a garage or workshop door. It’s one place I consistently have my phone (who doesn’t) and never have a place for it. Now I do.
Tangled up hoses can be frustrating and time sucks. So here's how to quickly uncoil…
Here's what really happens at an Extreme Makeover Home Edition project from my view as…
Need the best table saw for a mobile jobsite or DIYer? Look no further. Here's…
Selecting the right kitchen materials and appliances is essential so that your kitchen performs well…
Envisioning your goals for your kitchen remodel is a priority before you even consider getting…
We want you to be ready to take on your kitchen remodeling project confidently. Check…